Peugeot 3008 Key Fob Problems
Peugeot's mid-sized 3008 SUV has a lot of positives. It's stylish, it drives well and comes with a big boot. But is it capable of beating against strong competition in the most congested sector of the market?
If your Peugeot key fob isn't working, it may have been exposed to clean tap water or soapy water. It is possible to take off the battery and clean it with electronic cleaner or isopropyl alcohol.
Dead coin battery
Peugeot key fobs come with tiny coin batteries that powers their remote locking as well as other functions. This battery is limited in lifespan and wears out after years of use. One way to determine whether the battery is defective is to run a voltage test. A multimeter can test the voltage between the battery's plus and poles. This test can determine whether the battery is dead.
If you've been using your Peugeot 3008 for a while, and the key fobs have stopped functioning, it could be an issue with the receiver module. The receiver module is responsible for receiving radio frequency signals transmitted by key fobs and sending them out to the car's systems. If the receiver module is in problems, it won't be able transmit commands to other modules in the car.
Another common cause for a key fob that is not working is moisture or sweat that has accumulated on the circuit board. This can lead to short circuits that drain the battery and disable the remote locking feature of the key fob. If this happens then you must take your key fob to a chip level service technician to repair it.
Water damage
Water damage can cause problems in the event that you dropped your keyfob into the swimming pool, washed it or left it out in the rain. Water is a great conductor, and can easily cut off parts of the circuit board. It could also cause corrosion of the traces of metal and other components of the key fob. A wet circuit can also cause the battery to lose charge.
If you have a spare key fob, try using it to unlock or lock your Peugeot 3008 to eliminate the possibility that a dead coin battery is the root of the problem. Interference signals can cause your key fob to cease working properly. They interfere with the signals sent by the receiver module. These interference signals are caused by many sources such as radio transmitters in the vicinity.
If you hear sloshing noises emanating from your Peugeot 3008 when driving it could be caused by a blocked condensate drain from the evaporator. You can test this by blowing compressed air through the drain holes under your door. You can also use a flexible wire to wiggle the drain holes and dislodge any dirt that has collected there. Air pockets can also be indicated by sloshing noises.
The receiver module is not working properly.
The receiver module of a Peugeot 3008 is responsible for transmitting a remote keyless message from the keyfob into the receiver inside the car. This module could be damaged, preventing the car from acknowledging your key fob. This issue could be caused by the battery being dead or water damage. It could also be caused by interference from electronic devices operating on the same frequency. In these instances the car might display a message saying "card not detected" on the display.
There are many ways to resolve this problem. Try replacing the battery or reprogram the key fob. You could also make use of a spare key to start the car. However, if the fob isn't working even after these steps, it may be a chip not working properly.
It is best to remove the chip and clean it using rubbing alcohol and paper towel. If the chip is fried you should purchase a new one. The FB Series enclosures come with an accessory for battery holders for coin cells that can be used with the most popular types of key fob batteries. They can also be customized by using digital printing and CNC machined cutouts. If your key fob has been exposed to dirty or salty tap water, the chip could be contaminated and need to be cleaned.
Keyless entry system that isn't working properly
If you see "card not detected", this indicates that your car is unable to receive the signal from your key fob. This could be due to a number of reasons, such as the battery being weak or dead. The issue can be solved by pressing the start button on the key fob. In certain cases, you might require taking the keyfob to an Peugeot dealer for repairs.
Checking the battery is the first step to diagnosing the problem with a Peugeot 3008 keyfob which doesn't lock or unlock doors. Batteries are often the cause of a malfunctioning key fob. However, there are also other factors that could be at play. These include worn buttons, water damage, receiver module problems and signal interference.
If you've recently had your Peugeot key fob exposed to pure tap water it's best to remove the battery and dry the electronic components using paper towels. G28CarKeys can also use isopropyl Alcohol or a cleaner for this purpose. It is best to change the fob after it has been exposed to salt water or soapy water.
If your key fob still doesn't work You can reset it by removing the battery with 12 volts for 15 minutes. Connect the negative cable first, then the positive cable.